Cordless Drill Storage – Charging Station

by
0 comment

Hi!  I’d love to for you to follow me on Pinterest Her Tool Belt  and if you love instagram, you can keep up with me there too!

Our first monthly Reader Request Plan comes from Justin!  He wants a 5 dock cordless drill storage and battery charging station, that can hang on his garage wall.  What a great idea to corral your drills, batteries, and battery chargers in one place.  I thought it would be handy to include a drawer for drill bits and stuff. 

See it built


Please Subscribe

Need and different number of tool stalls? Or an easier build?

Check out these updated custom cordless drill organizer plans –> here <–

How to Build a Cordless Drill Organizer and Battery Charging Station

This post contains some affiliate links for your convenience. Click here to read my full disclosure policy.

Materials

Cut List

*Note:  This organizer fit perfectly with my Ryobi drills (old and new).  If the top of the handle, just under the head of your drill is larger than 1 1/2″, adjust the width of the bottoms (2 1/4″) accordingly.

Cut Diagram

This organizer is great for using up scrap 3/4″ plywood pieces. If you’re making it from a sheet of 3/4″, you can get 3 organizers from 1- 4’x8′ sheet.

*Note you can either make a traditional drawer bottom with dados and 1/4″ plywood, or you can kreg jig a 3/4″ bottom on. This cut diagram has a 3/4″ bottom in it (7 5/8″ x 16 3/8″)

Step 1

Cut out all pieces according to the cut list.  Get the 4 dividers and bottoms.  Mark 3/4″ in from each side of the bottom, to center the divider.  Pre-drill the bottom piece, unless you are using self tapping screws.  Apply a bead of glue and secure each divider and bottom together with 1 1/4″ screws.

Take one of the shelves.  Mark and pre-drill holes to attach the dividers to the shelf.  Glue and attach the dividers to the shelf with 1 1/4″, make sure the screws are flush or lower with the wood surface.  The gap between each divider is 3″.

Step 2

On the 2 sides, measure over and mark 8″ and measure up 10 1/2″ and mark.  Cut between the marks, removing the excess triangle.  Attach with glue and screws, the bottom side piece at the bottom inside of each side, flush with the front and bottom.

 

On the sides measure up and mark 4 1/2″ and 9 1/4″ from the bottom.  The gap between the shelves is 4″.  Pre-drill the sides, glue and screw the shelves between the sides.

 

Attach the back, between the sides.  Secure with glue and screws.

Step 3

Dado Drawer Bottom with 1/4″ plywood

Grab the 4 sides of the drawers.  Make dado cuts 1/4″ from the bottom, 1/4″ deep and 1/4″ wide.

If you have a Kreg Jig® R3 , you can make pocket joints on each end of the drawer sides (outside) to attach the drawer together.  If not, pre-drill holes through the drawer front and back.

Dry fit the drawer around the drawer bottom, check that it will fit in the drawer slot, trim as necessary.  Use glue and 1 1/4″ screws to assemble the drawer together.

Attach a drawer pull to the front of the drawer.  Sand the cordless drill station as needed.

To attach it to the wall, first locate studs in your wall.  You’ll also probably want it accessible to a power outlet.  Once you decide where to hang it, pre-drill holes in the back and attach it to the wall/studs with 3″ screws (2 minimum places).

Add a surge protector/power strip if desired and stock it full of your tools!

Download the Plans

click here–>Cordless Drill Organizer Charge Station Plans<–

Thanks Justin for the great project idea, have fun organizing you garage!

pin it for later, please

 

Related Posts

Leave a Comment